MHS Gold Edition Starkiller Contest Saber Build

[IG-88]

Well, I couldn't wait to see the results of the contest and am proud to have been a participant, and I am really proud of how I placed. :D

After seeing some of the Starkillers out there, I wanted to try my hand at making one. With that, I didn't want to make it exactly the same as many of the others out there. It had to be different, so I chose to go with a gold theme using brass. At first I had this buffed out to a mirror shine, but as the build continued, the brass started to patina into something nice. I then decided to make this a weathered Starkiller, which seems to fit the game better.

This was based off of MHS parts completely. The blade holder, ribbed extension modified by Tim at TCSS, the 4" double female, and the pommel were straight from TCSS. Many have said that an MHS Starkiller would not look right, but hopefully this build shows that is can be done.

Something to note is that I kept with the game spirit in that it has only 2 graflex short pins on the correct side. On the other side I used part of the brass graflex replica top cut out from the crystal chamber to make a round insert. It is held on by a bit of epoxy. It can be seen nicely in this pic:
http://i1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/th_DSCF0241.jpg (http://s1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/?action=view&current=DSCF0241.jpg)

Since I used the brass graflex top, I wanted to have bunny ears that matched the ones on a graflex. I purchased a graflex off of ebay that came with an extra graflex head with the bunny ears, but it supposedly got lost in the mail. That meant that I would either have to find another graflex or just make my own. I made them out of a brass kick plate. They are curved to match the curve of graflex bunny ears. They were a real pain to make, since they are one piece. I cut them out and bent them around. They took a lot of filing and sanding to have the curves look right. They are held on with a brass screw, and the threading is covered by a section of aluminum tubing.

The graflex top fit over the MHS parts because Tim lathed them down after customizing the ribbed section. I lathed the crystal chamber parts and a new heatsink out of aluminum to hold the crystal in place. The brass rods in the crystal chamber are held in place by holes in the heatsink and the crystal mount. They spin freely, but will not come out unless the crystal mount or the heatsink is removed (basically unless you take the entire thing apart). The crystal was taken from my very first build. The grips are made from brass key stock and held on with two 0-80 set screws each. I broke one of my 0-80 thread taps and had to hope for the best with my spare. The allen key for these things is a .035 allen wrench. The control box is made out of aluminum U channel I got at Lowes and a piece of brass stock I had on hand. The buttons are machined brass. The top is held on with epoxy, but can be popped off if needed.
http://i1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/th_DSCF0242.jpg (http://s1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/?action=view&current=DSCF0242.jpg)

PC-L Darkmeat
2 14500 Li-ion Batteries
5W LED Engine Red
Premium speaker
Momentary tactile switches
Custom Brass Covertec Kill Key
Custom Brass Bunny Ears
Lathed TCSS Blade Plug
Crystal Pommel
Red Button Thumbscrew as Blade Retention
Glass Eye thumbscrew for looks


I shorted the custom battery pack I had made after I installed it, so this is running on 2 14500 li-ions in a 2AA battery pack holder. It actually made screwing the back parts on a lot easier. It works for now, and has the recharge port connected. The kill key was made out of a brass covertec from TCSS with a little brass washer and a plastic tube (I think from a mechanical pencil).

The wires run from the main led up through a hole behind the heatsink up under the brass graflex top/under the control box and back down through a hole through the first rib to the main area. There are two wires barely visible underneath the point of the heatsink that touches the crystal. I barely had enough room to squeeze the wires up and around, so I am fine with the curve of a wire showing. If I were to do this again, I would make sure to make the heatsink larger to cover the hole, but in this case I did not have enough stock aluminum. If I were to replace the heatsink, the entire saber would need to be taken apart, and I do mean the entire thing, except for the grips.

And here are the pics. Enjoy.

http://i1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/th_Picture1.jpg (http://s1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/?action=view&current=Picture1.jpg)http://i1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/th_Picture2.jpg (http://s1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/?action=view&current=Picture2.jpg) http://i1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/th_Picture3.jpg (http://s1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/?action=view&current=Picture3.jpg) http://i1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/th_Picture4.jpg (http://s1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/?action=view&current=Picture4.jpg)
http://i1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/th_DSCF0237.jpg (http://s1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/?action=view&current=DSCF0237.jpg) http://i1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/th_Wiring2.jpg (http://s1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/?action=view&current=Wiring2.jpg) http://i1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/th_Wiring1.jpg (http://s1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/?action=view&current=Wiring1.jpg) http://i1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/th_Picture5.jpg (http://s1020.photobucket.com/albums/af330/polarcupz/Contest%20Saber/?action=view&current=Picture5.jpg)

Any comments and or questions are welcome! :D

[ARKM]

Awesome Starkiller saber.

[Skottsaber]

Totally epic, I loved it the moment I saw it!

[IG-88]

Thank you both. :-D

[iamdrake]

I hated that this saber was in the same poll as mine. I voted for yours... The attention to details is amazing. Great job.

[IG-88]

I hated that this saber was in the same poll as mine. I voted for yours... The attention to details is amazing. Great job.

Thank you for the vote. This saber was also owned by Borax's beast of a saber in that same poll. ;)

[bk_renesis]

That's a whole lot of brass goodness right there mate, too cool. Love starkiller sabers in any guise and this one is up there with my favorites. Love it!

[Crystal Chambers]

Great job. I really like it. I had thought about doing an MHS starkiller myself, or at least a variation. I knew something very very close could easily be done with some mods and a creative approach and you nailed it. I really like the crystal mounts and rails. I think the bunny ears might look better chrome but otherwise it still looks great. Since the bar has been risen this year, you still placed really well. Congrats!

[IG-88]

I wanted chrome bunny ears, but I was thwarted in my buy. I chose to go with brass, because a lot of the saber was brass. I could have gone with aluminum, but I don't think it looks bad. Thanks for the comments. :D

[Sunrider]

This is a great build. Love the brass. The details and construction look great. Maybe my favorite Starkiller!:cool:

[Loachri MacTalabh]

As far as Starkillers go? Your's is by far the best I have ever seen.

[IG-88]

As far as Starkillers go? Your's is by far the best I have ever seen.

The machining and scrap building can't compare to the VadersVault/Orbital Machining Starkillers, but it still turned out well. Thank you.

[Knighthammer]

Very good looking SK saber. I like it a lot, but a bit too much weathering for me personally. I tend to like mine clean, again though great job.

[ghost_a*]

this is the one i voted for. i'm obsessed with the starkiller lightsaber. awesome job!

[Darth Midian]

Dude, a brass Starkiller. That's awesome! The brass shroud & the red blade just look awesome together. Great job!

[Lord Dottore Matto]

You know. (yes, that was cryptic :lol: )

[Jedi Mynock]

This is what i voted on. amazing use of MHS parts with minimal machining to achieve something incredibly unique!
i am still trying to pice together a starkiller both in my head and with the saberbuilder... the MFX is okay but yours is proof that MHS can do just as good if not WAY better!

[ghost_a*]

what are you referring to when you say MFX?
i know MHS is the modular hilt system.

[Skottsaber]

MFX is the acronym for another saber "builder" who made a less than satisfactory version of the starkiller.

[sekrogue1985]

I dig like the gold yup!

[ghost_a*]

MFX is the acronym for another saber "builder" who made a less than satisfactory version of the starkiller.

ahhhhhhh, ok. i know who you're talking about. didn't quite put two and two together. thx.