equinox13
11-30-2010, 03:50 PM
equinox13's MHS4 - glacialis incendia
where to begin... a parts list i guess...
MHS exterior parts
Obi econo board - the LED outputs have the resistors removed and jumpered
larger vibe motor - Obi LED output resistored at 42 ohms
Blue P4 wired for stunt w/optional sound as always - also matches the AV switch LED perfectly ^_^
TCSS 'premium' speaker
recharge port and single 18650 Li-Ion
the paint on the non-black part is primer/baked, 2 coats hunter green/baked, and a very light coat of stainless steel so the green shows through/baked. the black parts were primered, dried naturally, then i put 4 light coats of ultra-flat black on, then baked them, then put on 2 more coats and baked that. then i rubbed my hands all over the black parts after eating to give them a bit of a 'worn' look. the screws were put in before painting.
underneath the rubber O-rings is a set of reverse sound holes - hence why i'm keeping the O-rings on. both to hide the holes and muffle/filter the sound. in the pommel i have the premium speaker in a speaker mount and a second pommel insert and 2 layers of foam padding to muffle the higher pitches and give it that nice deep thrum. ^_^
http://www.youtube.com/watch?v=E9yNW23Cios
http://lh6.ggpht.com/_k8Kp4lNYp8g/TPVy71hVMGI/AAAAAAAABG4/yCe8-44PnOM/s800/IMG_3327.JPG
http://lh6.ggpht.com/_k8Kp4lNYp8g/TPVy8jj2_3I/AAAAAAAABHM/k6m9HaCg0fI/s800/IMG_3329.JPG
http://lh6.ggpht.com/_k8Kp4lNYp8g/TPVy8zsBxxI/AAAAAAAABHQ/2HT0gpBJEcg/s800/IMG_3330.JPG
http://lh6.ggpht.com/_k8Kp4lNYp8g/TPVy9VtzESI/AAAAAAAABHY/6y0g23Cwwp8/s800/IMG_3331.JPG
http://lh5.ggpht.com/_k8Kp4lNYp8g/TPVzDMCHM6I/AAAAAAAABIQ/7QkbZ7sQdCc/s800/IMG_3339.JPG
http://lh4.ggpht.com/_k8Kp4lNYp8g/TPVzAOqOV3I/AAAAAAAABHc/9SZ54DtLUOU/s800/IMG_3332.JPG
http://lh3.ggpht.com/_k8Kp4lNYp8g/TPVzBHbZeNI/AAAAAAAABH0/lgxl-ZWO4Lk/s800/IMG_3335.JPG
http://lh5.ggpht.com/_k8Kp4lNYp8g/TPVzEEETiKI/AAAAAAAABI4/AgHMNQtoEA4/s800/IMG_3344.JPG
Gallery (http://picasaweb.google.com/azmariaxelloss/MHS4?authkey=Gv1sRgCM_eqt2Kh6uNlAE&feat=directlink)
where to begin... a parts list i guess...
MHS exterior parts
Obi econo board - the LED outputs have the resistors removed and jumpered
larger vibe motor - Obi LED output resistored at 42 ohms
Blue P4 wired for stunt w/optional sound as always - also matches the AV switch LED perfectly ^_^
TCSS 'premium' speaker
recharge port and single 18650 Li-Ion
the paint on the non-black part is primer/baked, 2 coats hunter green/baked, and a very light coat of stainless steel so the green shows through/baked. the black parts were primered, dried naturally, then i put 4 light coats of ultra-flat black on, then baked them, then put on 2 more coats and baked that. then i rubbed my hands all over the black parts after eating to give them a bit of a 'worn' look. the screws were put in before painting.
underneath the rubber O-rings is a set of reverse sound holes - hence why i'm keeping the O-rings on. both to hide the holes and muffle/filter the sound. in the pommel i have the premium speaker in a speaker mount and a second pommel insert and 2 layers of foam padding to muffle the higher pitches and give it that nice deep thrum. ^_^
http://www.youtube.com/watch?v=E9yNW23Cios
http://lh6.ggpht.com/_k8Kp4lNYp8g/TPVy71hVMGI/AAAAAAAABG4/yCe8-44PnOM/s800/IMG_3327.JPG
http://lh6.ggpht.com/_k8Kp4lNYp8g/TPVy8jj2_3I/AAAAAAAABHM/k6m9HaCg0fI/s800/IMG_3329.JPG
http://lh6.ggpht.com/_k8Kp4lNYp8g/TPVy8zsBxxI/AAAAAAAABHQ/2HT0gpBJEcg/s800/IMG_3330.JPG
http://lh6.ggpht.com/_k8Kp4lNYp8g/TPVy9VtzESI/AAAAAAAABHY/6y0g23Cwwp8/s800/IMG_3331.JPG
http://lh5.ggpht.com/_k8Kp4lNYp8g/TPVzDMCHM6I/AAAAAAAABIQ/7QkbZ7sQdCc/s800/IMG_3339.JPG
http://lh4.ggpht.com/_k8Kp4lNYp8g/TPVzAOqOV3I/AAAAAAAABHc/9SZ54DtLUOU/s800/IMG_3332.JPG
http://lh3.ggpht.com/_k8Kp4lNYp8g/TPVzBHbZeNI/AAAAAAAABH0/lgxl-ZWO4Lk/s800/IMG_3335.JPG
http://lh5.ggpht.com/_k8Kp4lNYp8g/TPVzEEETiKI/AAAAAAAABI4/AgHMNQtoEA4/s800/IMG_3344.JPG
Gallery (http://picasaweb.google.com/azmariaxelloss/MHS4?authkey=Gv1sRgCM_eqt2Kh6uNlAE&feat=directlink)