Jay-gon Jinn
05-22-2010, 05:40 AM
I had these extra parts laying around ever since Tim released the Jade style grip extension, but never really did anything with them up until a few weeks ago when I finally decided to make a brass saber using those parts. I picked out a blade holder (style 13) and I think it works for this particular design. I had to cut down 23 brass 1/4" screws to fit the grip properly, but I think it was worth it.
It took awhile to decide on a sound board, but after posting the build topic at FX-Sabers, I went with the general opinion expressed by the members and used an MR Jedi board instead of the Ultrasounds I have available. It was much easier to wire up the pommel led and the switch that way anyway. I almost went another route with the battery solution, but decided to keep it simple and just used a 4-AAA holder, and modified the speaker mount for rear venting as I did on CS-26, and then drilled the choke for sound vents, too. It worked out pretty well, and you can certainly "Feel the Force" when you grip this saber by the choke and activate it!
So with out further ado, here is my
Brass Saber 21
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7701.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7702.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7703.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7704.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7705.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7706.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7707.jpg
Would you believe I completely eye-balled this hole pattern? Well, I did!
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7708.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7709.jpg
I had to modify the brass CT wheel by sanding the dish flat to make it fit on the Jaded grip section. The screws were too close to the CT wheel originally to allow it fit flush as it was designed to. I also added a lock washer to act as a spacer so that the CT wheel fits similar to the one found on a Mace Windu FX.
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7711.jpg
My camera seems to want to show the pommel led as blue, but it is lighting up a faint purple, actually.
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7716.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7712.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7713.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7714.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7715.jpg
YouTube Video: http://www.youtube.com/watch?v=3LRZdQHwH0s
It took awhile to decide on a sound board, but after posting the build topic at FX-Sabers, I went with the general opinion expressed by the members and used an MR Jedi board instead of the Ultrasounds I have available. It was much easier to wire up the pommel led and the switch that way anyway. I almost went another route with the battery solution, but decided to keep it simple and just used a 4-AAA holder, and modified the speaker mount for rear venting as I did on CS-26, and then drilled the choke for sound vents, too. It worked out pretty well, and you can certainly "Feel the Force" when you grip this saber by the choke and activate it!
So with out further ado, here is my
Brass Saber 21
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7701.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7702.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7703.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7704.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7705.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7706.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7707.jpg
Would you believe I completely eye-balled this hole pattern? Well, I did!
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7708.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7709.jpg
I had to modify the brass CT wheel by sanding the dish flat to make it fit on the Jaded grip section. The screws were too close to the CT wheel originally to allow it fit flush as it was designed to. I also added a lock washer to act as a spacer so that the CT wheel fits similar to the one found on a Mace Windu FX.
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7711.jpg
My camera seems to want to show the pommel led as blue, but it is lighting up a faint purple, actually.
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7716.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7712.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7713.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7714.jpg
http://i119.photobucket.com/albums/o141/Jay-gon_Jinn/Brass%20Saber%2021/100_7715.jpg
YouTube Video: http://www.youtube.com/watch?v=3LRZdQHwH0s